11/10/26

More Compound Pendulum Physics as related to Escapement Efficiency

 A builder asks:  I want to pick your brain about pendulums. I'm thinking of Organic and Flight. Organic is perfection, the way you dropped the center of gravity and curled the pendulum around. I understand the bob at the top to adjust the timing and how critical the weight is.

Then I moved to Flight. When you sit down to design that pendulum, other than cutting out a trial pendulum and weighing it, how else can you begin to predict how much that pendulum will weigh, and therefore work? Or do you just empirically keep working at it until it does?

I see that you keep the center of gravity low, by expanding the lower pendulum leg from the pivot point.

 I know the length of the pendulum with the Bob creates the 2-second cycle.
Thanks, 
Eric


More Compound Pendulum Physics as related to Escapement Efficiency

The mass of a well balanced horizontal pendulum is, within reason, almost irrelevant if one keeps in mind that it is easier to push a child on a swing than an elephant.  Moving the mass of the horizontal pendulum is the job of the clock's drive weight, gear train, and an especially important consideration is the efficiency of the escapement itself.  

Take for example the SwingTime (or Mantis or Flight) and Organic, all of which have compound pendulums.  The SwingTime (or Mantis or Flight) clockworks cannot be driven by hanging drive weights using the usual one inch diameter drive pulley barrel.  There is simply not enough torque produced from the pulley barrel's 1/2 inch of leverage to be transmitted through the gears into that inefficient escapement to run the clock.  SwingTime requires that it be driven by a motor arm transmitting its torque through the large center wheel...and it must be a relatively large center wheel diameter, too, to create a large enough lever.  I tried running a clock with SwingTime's escapement with a smaller diameter center wheel and even after adding significant additional weight onto the motor arm, it still did not have enough torque to run that particular clock.  A long lever is required.

Inline image

The picture above shows what kind of lever one might need to move an elephant.

On the other hand the Organic has a very efficient escapement and using this extended lever motor arm on the already large diameter center wheel almost overpowers that clock design.  Organic is almost unstoppable.  I have to stick a pencil in the gears to keep it from starting on its own.

So the mass of a horizontal pendulum, again within reason, is more a consideration of the type of gear train and escapement that one uses to drive the pendulum.

Once a horizontal pendulum, of pretty much any reasonable mass, is perfectly balanced, it takes very little force to keep it in motion once set into motion.  (Organic is so efficient that it doesn't even need to be set into motion ~ it starts itself.).

The beat or timing of the pendulum is created by the relative masses above and below the horizontal pendulum and their location relative to the pivot point.  Those are the upper and lower bobs, one of which is fixed and the other adjustable, depending upon the clock's particular design.  SwingTime, Organic and Flight all have adjustable upper bobs and fixed lower bobs.  Mantis has a fixed upper bob (the antennae) and an adjustable lower bob.

You may enjoy going back and reading my Pendulum Physics blog post on compound balance pendulums of 09 04 2022.  The above information is explained again in that Blog post somewhat differently than I have explained here.  https://claytonboyer.blogspot.com/search/label/Pendulum

So why do I design with the inefficient escapement of the SwingTime, Mantis and Flight?  Because I love seeing that excessively huge, beautiful pendulum swing that it produces.  The escapements inefficiency imparts a magnificently exaggerated movement to the pendulum.  Anyone who has stood in front of Mantis or Flight knows how relaxing and mesmerizing that huge, slow pendulum swing can be, and what a delight it is to watch each of these mechanisms displaying their dramatically exaggerated pendulum kinetic joy.

5/7/25

Celebrating Simplicity's 20th Birthday


Since our Simplicity has run now for over twenty years, just for fun I calculated the number of times Simplicity has swung its pendulum in those two decades. I was amazed to find that this clock has ticked and tocked over 315 million times! That is a number that is almost too large to comprehend, and yet our Simplicity happily continues on with its daily duties without complaint.

Our Simplicity is as happy today as that day, twenty years ago, when I gave its pendulum the gentle push that stated this amazing journey. And, look closely at the picture, you'll see that our Simplicity shows no wear at all! But best of all, this clock has been completely trouble-free all that time. I don't recall my wonderful Simplicity ever giving me a single problem. I just wind it, and it runs. Looking at its wear patterns, I would estimate that it probably has another two or three hundred years before it begins to show any signs of its age. I'll check it in a couple hundred years and keep you posted.

 For its first few years that Simplicity kept me company out in my shop where its beautiful song would be the first thing to greet me in the morning when I opened the shop doors. But out there with the constant Hawaiian trade winds to contend with, it would also be exposed to salty humidity and be constantly accumulating dust and, of course, be routinely covered in sawdust from my other woodworking activities. With that accumulation of humidity, salt, sawdust, at certain point, it would eventually stop ticking. I felt sorry for it. Having to put up with all that humidity, dirt and dust, must have been a challenge, however it never really complained. And the fix was so simple! With a few blasts of compressed air that beautiful Simplicity was ready to go out dancing once again.

Today that same Simplicity is featured as our living room clock, where it shares the opposite side of our fireplace mantle with the Zinnia. Simplicity and Zinnia make spectacularly beautiful fireplace finials.

Simplicity is the second clock that visitors see when they come into our home. The first clock visitors see is the Arts&Crafts in the foyer. The A&C is an electromagnetically impulsed clockworks. All of these mechanisms are such a delight!

As you probably have read in the Instructions sent with your plans, it is best to stop the pendulum each time that the clock is going to be rewound. This helps preserve the delicate pendulum, pallet adjustment. Then, once the clock is rewound, the pendulum can be restarted. After ten or eleven years of stopping that pendulum every time I rewound the Simplicity, I wanted to create a way to rewind the clock without having to stop and start the pendulum, and yet still allow the clock to maintaining the proper pendulum/pallet adjustment. My idea was to create a maintaining power arm that could be temporarily added to the large center wheel during the rewinding process...and it works beautifully! That Maintaining Power Arm now rests, along with the Speed-O-Key, on the shelf behind the Simplicity's center wheel. But I still have the original Simplicity key on display because it is such a beautiful showpiece of wood art.

If you have the Simplicity plans and would like to make a Maintaining Power Arm for your clock, simply email me a request and I'll be happy to send you the pdf.

I hope that you choose to build a Simplicity. I also hope that you enjoy living with your clock the next twenty or...maybe three hundred years.

After decades of building lamps, chairs, tables, bowls, cabinets, kitchen items, kinetic sculptures, automata, etc. I am convinced that these clocks are absolutely the VERY BEST way to spend time in the shop. I hope that you think so, too.

2/3/25

Robot Design



Builder Steve asks Clayton, "I’m intrigued to know how you design these robots. Do you use Meccano to test out varying options?"

Clayton answers: 
I've never had a Meccano set, but I think having one would have been a boon to my creativity.

I design in my head, then I draw, and test, and test, and test, draw some more and re-test.  Eventually I either give up, or have a success.

You can see one of my failures below.  Cracks me up every time I watch it.  Virtually nothing is successful the first time.

12/3/24

Creating an Accurate Escape Wheel

If your accuracy at the scroll saw happens to be a bit lacking, here are four steps to help you create a wheel with a high degree of accuracy. 

I chose the escape wheel for this demonstration because the escape wheel has the most exacting requirements of any of the clock's train of wheels.  However, these four steps can also be successfully applied when creating any of the clock's other wheels.

The parts shown in green on each picture are the parts to be cut or sanded at that particular step.

11/20/24

Whirly in Color!

 


Master Gear Wizologist Ken Duffy created a wonderfully customized and multi-colored version of the Whirly. Ken not only added delightful colors, but he also created a third way to power the Whirly. The original Whirly is powered by either a drive weight or by a constant force spring. Ken has powered his colorful Whirly with an intermittent motorized rewind.

For those of you that have already purchased the Whirly plans, or new plan purchasers that find Ken's customizing concepts interesting, contact Clayton. Links and motor arm information to upgrade your Whirly are available upon request.

8/5/24

(AH) Alignment Hole Click Gear

Steve asks Clayton: 

I've noticed on the Swing Time plans the notation "AH", which I hadn't seen on other plans I bought before.

Maybe I missed it, but what does "AH" stand for?

Thanks
Steve 


Aloha Steve, when parts need to be reinforced during gluing, or need to be aligned in a specific orientation, I will add alignment holes (AH) notations to the plans to be sure that the parts are aligned correctly.

In the SwingTime plans that you are working on, the parts of the Daisy Dial Train need to be aligned correctly to get the hour and minute hand assembly to work properly.  

The Daisy itself has an up and a down.  The cleft in the Daisy needs to be positioned UP, and the rounded bulb placed at the bottom.  The exact alignment can be achieved between the Daisy and its Support by inserting a short length of rod into the alignment holes during gluing.  These rods can be left in place, or they can be removed after the glue has dried.  In this case the choice of leaving the alignment rods in place or removing them is up to the builder.

Also in addition to positioning the Daisy on its Support, the Tri needs to be positioned correctly on the Daisy's Hour Hand so that the the Hour Hand is pointing in the proper direction to show the correct time once assembled.

For both of these situations exact alignment is produced using the Alignment Holes (AH) provided in the various parts.

There is another situation in which alignment of other parts, such as gears, is critical.  For example, in the Genesis plans there is a "wheel set" (a pinion and a large gear) that need to be aligned during assembly.  Alignment holes in those parts show the builder how to achieve the correct alignment of the teeth of these gears that will allow the clock to show us the correct time.  

Other times you might see Alignment Holes in the Click Gear and its Support in the rewind system of the clock.  In this case we Do Not want to remove the alignment rods after the glue has dried between the parts.  The alignment rods in this situation allows for a stronger joint between the parts than what is provided by just the glue.  The reason for this additional strengthening of that glue joint is that the Click Gear must support the entire drive weight of the clock.  We certainly don't want the Click Gear breaking loose from its Support.  Leaving the alignment rods in place allows for a bit more insurance against separation of that glue joint, and helping to prevent the drive weight crashing to the floor.  "Drive Weight Crash (DWC) Prevention" is also why I recommend using only the highest quality plywood when creating the Click Gear and Clicks.

BTW...once the Click Gear is glued and pinned to its Support or Pulley, I also add a coating of cyanoacrylate glue (CA or Super Glue) to the tooth surfaces of my Click Gear ~ just for a little more insurance against Drive Weight Crash.  That additional procedure of adding the CA may be overkill, but I'm superstitious.  (I've also learned to stop listening to the voices that come out of the electrical box in the attic storage room)

In over twenty years of creating these wonderful mechanisms I have only had one DWC...and if you've ever had one, you know that one DWC is one to many.  So using high quality ply to make the Click Gear and Clicks, and the addition of the support pins to assist holding the rewind system's glue joints together, will help to avoid the dreaded Midnight Crash Syndrome.  

I hope you are enjoying your build and please send pictures when you get your SwingTime completed.  

Aloha.  Clayton

12/29/23

Help! My Clock Runs too Slow (or too Fast)

 FOR A CLOCK THAT RUNS TOO SLOW...(but also be sure to read over the section below on "For a clock that runs too fast"). 

If you have recently finished your clock and put it into beat and it's running too slowly - I recommend you do nothing for four to six weeks. 

Some time ago I got an email from a builder whose Simplicity ran too slowly at first, he cut off the pendulum...only it was too soon.  When his clock eventually found its beat, it then ran too fast.  I recommend waiting a few weeks before shortening a pendulum shaft because it is much easier to cut off a pendulum than to add to it. 

Some clocks need to run a while before they find their "beat".  It is best to simply watch a new clock for a few weeks.  Stand back and enjoy viewing its motion, and congratulate yourself for getting a chunk of wood to move.  Just enjoy the movement. 

If your clock still runs too slowly after it has run for a few weeks, then you can begin to shorten the pendulum's shaft a little at a time, until you get your clock running at the perfect beat. 

But even before cutting off the pendulum, I would recommend that you read over the "Depthing" procedure in my Troubleshooting Blog posts and in my FAQ's, and follow those instructions.  Depthing will help to free up any residual internal friction in your clock and possibly make it run more freely.  The links to my Blog and FAQ's is at the bottom of my main page. 

You can also add just a slight bit of paraffin to the tooth contact surfaces where the pinion and wheel teeth touch.  Add just a very slight amount - because too much paraffin can clog the dedendum and make the clock stop.  Candle wax works okay, but I like to use a color coordinated Crayon.  Crayon paraffin is softer than candle wax, and that sharp point makes getting between the teeth much simpler. 

You can also remove the pallets, wind your clock, and let the gears run free.  When the wheels stop, rewind the clock and let it run free again a few times.  Things get spinning pretty fast!  But sometimes this helps to "break in" the mechanism more quickly. 

If/when you have done all of the above suggestions and your clock is still running too slowly with the bob all the way up as high as it will go on the pendulum; to determine how much of the pendulum to cut off you can measure the threaded rod sticking out the bottom of the bob, and remove about half that length from the pendulum's shaft...but be sure to wait a few weeks before cutting the pendulum to give your clock time to 'break in' and find its beat. 

FOR A CLOCK THAT RUNS TOO FAST...(but also read "For a clock that runs too slow" above.) 

If you have just put your clock into beat, leave all alone and just enjoy the movement for four to six weeks.  Some clocks run fast, others too slowly when first put into beat and they require a "break in" period to find their beat.  I recommend during this time to just stand proudly in front of your clock and pat yourself on the back for doing such a good job of getting a chunk of wood to move. 

After the break in period if your clock is still running too fast (and it depends upon how fast) two things may be happening.  If your clock is gaining minutes a day, you can try to simply make the bob heavier, and/or lengthen the pendulum by a few inches.  If your clock is gaining hours a day, something is probably slipping inside the clock's train and you'll need to investigate further to find the broken, unglued, or unrestrained part. 

Certain escapements, like the Graham, are not very sensitive to drive weight, but others, like the grasshoppers and the "walking" on the HO, and the verge and foliot on the Wee Willie and Horologium are quite sensitive to drive weight.  If your clock is running fast, try to decrease the amount of drive weight.  Also read the section on "Depthing" on my site in my FAQ's and the four informative Troubleshooting posts in my Blog.  The links to these can be found at the bottom of my main page. 

As I mentioned, if you just put your clock into beat, it is best to not do anything for a few weeks except enjoy the movement.  After that time you'll want to check the bob weight by adding fish weights evenly on each side of the bob, and/or increase the pendulum's length depending upon how fast the clock is running. 

Take a look at my Attempt for an easy way to add length to a pendulum. 

Also, you'll want to do all of this where the clock will actually be permanently mounted.  It's weird, but sometimes just moving the clock from the shop to the house can cause the clock to run faster or slower (I have no explanation as to why, but it has happened a few times to my own clocks). 

Enjoy! 

Aloha.  Clayton

9/13/23

Relative Seasonal Stability of Various Woods used for Pendulums

Question from reader:  How accurate is your Number Six Clock?

My Number Six clock is quite accurate.  It is usually nearly spot on, but sometimes can run within about a minute or two a day depending on ambient atmospheric changes.

If you maintain a constant heat and humidity in your home, a pendulum clock will maintain better accuracy.  If your home has huge heat and cooling swings, or huge changes from humid to dry air, then any pendulum clock will also show less accuracy, this even includes clocks with metal pendulums.

The pendulum is the timing unit of any clock. A clock's accuracy is determined by the pendulum, and not by the gears.  However, the stability of the material used for the pendulum can affect the clocks accuracy.

A very stable wood used for a pendulum shaft is going to be a more accurate pendulum than a wood that changes a lot with changes in the ambient heat and humidity.  So if accuracy is top of mind, we would like to know the "Relative Seasonal Stability" of the woods we choose for our pendulum.

The way the wood is cut from the tree also has an effect on the stability of the final pendulum.

There are three ways wood is cut from a log; 1) Flatsawn (AKA Plain Sawn), 2) Riftsawn & 3) Quartersawn.  The stability of the final product from those cuts is also in that same order.

Flatsawn (the kind of wood that most of us have readily available) has the least stability to changes in heat and humidity.  Riftsawn is quite stable and can give better results when used as a pendulum, but the very most stable cut of wood is the Quartersawn.  Here is a picture that describes the three different ways wood is cut from a log.


With that being said, even Flat or Plain Sawn wood make excellent pendulums because the grain of the wood is almost assuredly going vertically throughout the entire length of the pendulum.  Flat or Plain Sawn wood has about the same stability to atmospheric changes as a solid metal rod.

Flat or Plain Sawn wood make excellent pendulums, and except for some plywood pendulums, Flat Sawn wood is generally the only type that I ever use on any of my clocks.

Here is a chart that shows the relative stability of wood by species and cut.  Since most of use can only get (or afford) Plain/Flat Sawn wood, compare the examples of White Oak (9.1) and and Honduras Mahogany (4.1).  The Flatsawn Mahogany has more than twice the Relative Seasonal Stability of the Oak.

So according to this chart if you had a choice of Oak or Mahogany, and you were shooting for the best accuracy from your pendulum, you would absolutely prefer your pendulum being made from a close grained wood such as Mahogany.

10/1/22

Graham Escapement with Pendulum Adjustments

Builder Joe has a question about Graham escapements:

I have another question regarding my pendulum slowly stopping.  In your FAQ (on our website):

"Now when you get to the escape wheel, put the wheel in with the pallet arbor.  When the pallets are in proper position, gently restrain the pallets with your finger on the arbor.  Now turn the escape wheel.  It should first push one of the pallets out of the way, and this will cause the other pallet to come into contact with another escape wheel tooth.  Keep turning the escape wheel and the pallets should gently rock back and forth."

Should the pendulum be on it?  I have tried without the pendulum, but I can’t get the pallets to keep rocking.

Thanks again, Joe

Clayton answers:

The entry in the FAQ's describes a manual test of a Graham escapement.  It is a check designed to let you determine if the pallets and escape teeth interact correctly all the way around the escape wheel.  

However, what is described there is only a manual test.  Once the pendulum and the drive weights are added and the clock is put into motion, we introduce inertia that will cause the pallets and escape wheel to interact differently than described in that manual test.  In a working clock the pendulum's inertia will move the pallets further than will happen during the manual test described in the FAQ's.  The drive weights will cause the escape wheel to move faster than it does during the manual test.

Slowly moving the escape wheel by hand, and restricting the pallet arbor, should give your Graham pallets a nice rocking movement as the escape teeth move gently from one pallet face to the next pallet face.  Manually restricting the pallet arbor as described in the FAQ's, the pallet arms should not be involved.  




But when the weights and pendulum are added and the pallet arbor free to move, as in a fully functioning clock, more movement is introduced into the mechanism and the pallets are not now stopped by the their faces, but instead are stopped by the side of the pallet's arm.

The FAQ check is a manual check of the escapement.  It is something you can do to test function while the clock is being assembled and laying on its back on your workbench.

However, the actual movement of a fully functional escapement with drive weights and pendulum will be different.

Here is how a fully functioning Graham escapement works...

The pallets are first stopped by the side of the pallet arm.  The escape wheel is held completely still by the side of the pallet arm until the pendulum has completed its motion and reversed its direction.  Then the escape tooth is released from the pallet's arm and the tooth slides across the pallet's face - giving impulse to the pendulum, and simultaneously causing the next pallet arm to enter between the teeth, which puts the opposite pallet arm in the way of the escape tooth on the other side of the escape wheel.


With an understanding of the step-by-step motion of a Graham escapement explained, in the video below we can actually see it all happening.



If your pendulum is slowly coming to a stop, there are a few issues that need to be addressed.

First, do you have enough drive weight to power your clock?  Every clock is different and will have its own minimal drive weight requirement.  Check out my Blog post on Drive Weight for a way to determine just how much drive weight your specific clock actually needs. (link to my blog is at the bottom of the main page)

But what if you find that your clock needs excessive drive weight to power it?

If your clock is in need of excessive drive weight, the second issue to be addressed is the depthing of each wheel set in the clock's train.  This Depthing procedure is described in detail in the Troubleshooting section of my Blog 

The third issue to be addressed is a test specifically for the action of the pendulum/pallets and crutch.  For this test you will want to remove the escape wheel from the system as we will only be testing the pendulum/pallets/crutch assembly, and all of their associated arbors, and spacers.  

With the escape wheel removed from the system, but with all of the parts of the pendulum, pallets and crutch still working together, pull the pendulum's bob about three or four inches to one side and let it go.

The pendulum/pallet/crutch assembly should continue to rock for at least 60 seconds before stopping.  And 90 seconds is even better.

If your pendulum does not continue to oscillate for at least 60 seconds, we need to find out why.  We need to find what is restricting the movement of the system.

One of the most common reasons is that the groove that the knife edge of the pendulum pivot sits in has been carved too deeply.  That groove should be about 1/32" (.75mm) deep.  A too-deep groove will add excessive friction to the knife edge of the pendulum and restrict its freedom of motion. (this does not apply to the clock designs using bearing packs)

Another area that should be checked is the interaction of the crutch pin and crutch.  

If the crutch pin fits too tightly into the slot in the crutch, the binding friction will stop the clock.  

If the crutch pin fits too sloppily into the slot in the crutch, the impulse from the pallets will not be transferred to the pendulum, and the clock will stop.

The crutch pin should fit in the crutch slot and be free, but not sloppy.  As a measuring tool, you should just be able to slip the corner of a sheet of paper between the crutch pin and the side of the crutch slot.


9/4/22

Pendulum Physics

 Clayton,

In your written instructions for the Mantis clock you say to slow the time adjust the Bob up and to speed the clock turn the Bob down. Isn’t this backwards?

I thought to slow the clock you make the pendulum longer and shorter to speed it up. 

Thanks, Cal 

Cal, your query got me thinking that I should create a blog post explaining about the various types of pendulums and hopefully make their action simpler to understand.

There are basically three pendulum arrangements used in modern clockmaking.  These are shown in the Pendulums jpg below.  It is important to notice first that "0" is the pivot point.

Fig 31 shows a standard straight hanging "simple" pendulum with the pivot at the top.  Most of my clock designs use this type of pendulum.  It's fairly simple to understand.  If we raise the bob, it speeds the clock.  If we lower the bob, it slows the clock.  The longer the pendulum shaft, and the lower the bob, the slower this type of pendulum will oscillate.  We can also slow the oscillation of the clock by increasing the mass of the bob. With this style of pendulum, a very short pendulum shaft, or very light bob, will oscillate much faster.

Fig 32 shows a compound balance pendulum.  This is the style of pendulum used on the Mantis, Celebration, Balance, Organic and SwingTime and others.  Compound balance pendulums have the most variation, and are the most difficult to understand...but are pretty cool, because of their versatility.  For example, we could create a compound balance pendulum that is very short, say only 15 inches (38cm) tall, to take the place of a standard "simple" pendulum (Fig 31) that would need to be 42 inches (107cm) long.  Of course, we can make our compound balance pendulum shorter than 15", but the shorter we make them, the touchier, and more difficult to adjust it would become.  I saw one metal clock with a compound balance pendulum that was only three inches (7.5cm).  However, that's a bit unrealistic for our wooden mechanisms.

Fig 33 shows the pendulum arrangement used on the Toucan and Arts&Crafts clocks.  There is a stationary bob at the bottom of the pendulum shaft, and an adjustable bob between the stationary bob and the pivot.  Although it is a variant of the compound pendulum,  this type pendulum works much like the pendulum in Fig 31.  Raise the bob (or lighten it) to speed the beat, and lower the bob (or add more bob weight) to slow the clock's beat.

This morning I was sitting on the couch reading a book and it hit me how to answer your question and explain a compound balance pendulum's action.  It all has to to with what is called "Restoring Force".  The force exerted on the pendulum by gravity.

With a heavier bob on the bottom of the pendulum shaft, there is more restoring force on the bottom.  That's simple to imagine.  (we will not be concerned here with oscillations - only the effects that gravity has on the restoring force of the pendulum)

Think about a pendulum that pivots in the center, like the pendulum example that is shown in Fig 32.  But in our example here, instead of the pendulum being vertical, think of it horizontally.  (if you want a visual, simply turn the Pendulums jpg 90 degrees and look at Fig 32)

With the pendulum shaft being held horizontally, add a stationary, immovable weight at the very end of one side of the shaft, and then add a heavier, adjustable weight to the other side.  Don't let go of it yet.  Keep holding it horizontally.  If you move that heavier bob inwardly toward the pivot until it balances with the lighter, stationary bob at the other end, the pendulum has no restoring force.  You can let it go and the pendulum stays at rest horizontally.

With that same horizontal pendulum arrangement in mind, move the heavier bob down the shaft away from the pivot just a fraction of the distance so that the pendulum is no longer perfectly balanced.  Let it go and the pendulum will begin to move.  The heavier side moves down toward the floor, and the lighter side moves up toward the ceiling.  You can imagine that if the imbalance is very slight that the movement of the heavier side toward vertical is quite slow.

In a second experiment, holding the pendulum at balance horizontally, move the heavier bob all the way out to the extreme end of the pendulum shaft, and let the pendulum go.  The pendulum will now move quite fast to the vertical position (and overshoot vertical, thus the pendulum will oscillate a while.  But we are not concerned with oscillations here.  We are only concerned with the speed at which restoration takes place.)

In the first example with the heavier, adjustable bob essentially raised up (in) toward the pivot, the pendulum has little restoring force and moves slowly to a vertical position.  (thus, when lower adjustable bob is raised it causes slower restoration)

In the second example with the bob lowered toward the bottom end of the shaft, the pendulum quickly moves under the influence of gravity to the vertical position.  (thus, when we lower the adjustable bob further from the pivot it causes faster restoration).

Since Mantis has a compound balance pendulum, as shown in Fig. 32, by raising the bob up toward the pivot the motion of the pendulum is slowed.

We can also slow the Mantis pendulum another way; by lightening the lower bob.  A lighter lower adjustable bob has less restoring force.

SwingTime and Organic have compound balance pendulums also, however unlike the adjustable lower bob of the Mantis, their lower bob mass is not adjustable and stays constant.  On these clocks the upper bob is the bob used to adjust the beat.  Fortunately, the same "Restoring Force" physics apply whether you are adjusting the upper bob or the lower bob.  On a pendulum with a constant weight below the pivot, if we raise the bob that is above the pivot we slow the beat of the clock...alternatively, we could simply make the upper bob heavier.  In this case of an upper adjustable bob, both a heavier bob or raising the upper bob have the same effect on the restoring force of the pendulum.

One more, just for fun.  I created a clock that is yet another variation of Fig 33.  This clock is ALL pendulum.  The only part that is not pendulum is the wall mount.  Everything else is contained in or on the pendulum.  I call this clock "Minimalist."



Since the clockworks is integrated into the pendulum we have a compound balance pendulum that is similar to the Toucan or Arts&Crafts, except that in this case the center bob (the clockworks) is stationary, and the lower bob is the adjustment for the beat.

Because of the clock being integrated into the pendulum, the mass of the pendulum has increased and thus we need lower the bob with a longer pendulum shaft than would normally be the case.  Most of my "Simple" seconds pendulums are around 42" (107cm) from pivot to center of the bob.  The Minimalist pendulum requires about 63" (160cm) to give a seconds beat.  My purpose for this clock was to stretch out and thin down the overall appearance of the mechanism.  Integrating the clockworks into the pendulum allowed me to do just that.

Thin, slim and streamlined, Minimalist is a lovely clockworks with a unique pendulum.

Daisy Dial Train Puzzle

Dear Clayton,  I have a small issue with the Daisy Dial Train on my Mantis. The hour hand consistently stops at about 4:00. It happens pretty much every time that the hour hand attempts to pass roundabout 4:00. 

Since this is consistent, I figure that there is probably a known solution, and maybe this is common. 

The only item that comes so mind for me is the balance of the hour hand. If the hour hand isn’t well balanced, and the short end of the hour hand is heavier, this might explain the consistent stopping at 4:00. Thoughts? 

Just wondering about this. Since it’s so consistent, maybe you have a quick solution? 

Clayton's response:  Aloha.  I'm happy to help.  As you know, the Daisy Dial Train is such a wonderful and unique part of many of my designs - Radiance, Mantis, Balance, SwingTime, Tempo - all use the Daisy Dial Train.   It is such an excellent dial train for very quickly setting the hands to the correct time. 

I think your guess is a good one about the Hour Hand's counterweight end being just a bit heavy, and that should be checked out.  

Checking a hand's balance is easily tested by removing the hand and running a rod through the center hole of the hand and giving it a spin.  When the hand stops spinning, the heavy part of the hand will be pointing at the floor.  Then to balance, remove some wood from the back of the heavy end, or add some weight to the counterweight end.  

However...my first thought was not of the Hour Hand counterweight.  It was instead of the Daisy itself and its interaction with the pins coming out the back of the Tri. 

A most common cause of the Daisy Dial Train not working properly at first is that the pins get stuck on the Daisy's bump as they are trying to pass over.  Once the reason is found and fixed, the Daisy can continue to give decades of flawless motion. 

This sticking of the pin on a bump can be caused by a too-large, or unsmooth bump.  Or it could be that the drilled dowel, that is the Cam of the Minute Hand, does not have enough lift to get the Tri's pin smoothly over the bump.  Here is a screenshot from the bottom of the Minute Hand assembly page that explains... 


 Alternatively, an Hour Hand consistently getting stuck at one point on the dial could be something as simple as the Daisy bump needing a bit of lubricant. 

Since it is such a simple thing to investigate, that is where I'd begin looking. 

I'd first see what pin/bump is getting caught upon (there may be two of the three pins each caught on a bump), then I'd get out my color-coordinated Crayon and add a little paraffin to the offending bump and pin.  It wouldn't hurt to put a bit of paraffin on each of the bumps and each of the pins.  And then back off the Allen screw and leather plug and give the Minute Hand a spin like I show in the attached video.

 


Please keep me posted.  Let me know what you discover and what you did to fix this puzzle. 

Aloha.  Clayton

4/5/22

Excellent Mantis Build Video by Brian Gray!


Brian Gray made this wonderful video of his build of the Mantis clock from cutting to assembly to fully working clock.  He sent us this link, plus some very nice compliments.  Thank you, Brian!

Clayton writes:

Wow!  This is an amazing video, Brian.  You've done an excellent job constructing your Mantis wooden clock build, but you've also done a great job showing how you did it.  You have an amazing workshop with so many excellent tools.  I was drooling!  Your shop makes mine look pretty meager.  Beautifully done, Brian.  You have shown the way these projects are approached by a true craftsman.  I'll certainly be referring this video to other Mantis builders.  Well Done!  Aloha.  Clayton

 Brian answers:

Thank you Clayton! It's been such a pleasure to put together a few of your clock designs, with more coming! I've been a machinist and woodworker for more than a few decades now. But for some reason, clocks have put a huge spark into my inspiration like no other projects in the past. Thank you very for taking the effort to make your plans available. I'm sure that creating an accurate set of plans is much more work than the clock itself, so thank you!

2/6/22

Perfect Involute Tooth Forms?

Interesting question from a builder:

I'm new to wood clocks, but have some mechanical engineering experience. I see that the tooth profiles on the pinions are nothing like those on the wheels they drive (and neither look like involute teeth). 

Why the difference in tooth profiles? It seems to me that the two ought to be the same. To add to the question, it seems to me the quasi-trapezoidal teeth on the driven wheels would be easier to cut accurately, suggesting the pinion teeth should be similar. What do you say?

Regards,
John

Aloha John, it is nice to hear from you.

Your engineering experience has taught you right.  It has taught you about high speed gearing at its finest.  

Thing is...clocks don't move fast so that level of perfection is not required.

As a matter of fact, in my own experiments, it's difficult to notice any difference at all with various tooth forms.

I discuss this at length in my book, Practical Guide.

Take a look at the various tooth forms that I use in my designs.  You'll see straight sided, involute, "random", rounded, and none of them seem to perform much better than any other.

You can make high speed, "perfectly" engineered teeth if you like, but do some experiments on your own and I think you'll convince yourself that pretty much any tooth form works well at low speeds.

The old tymers used to cut triangular tooth forms.  Worked fine for them.  Hacked them out with adz and axes.

Take a look at the teeth on this old clock on the cover of the National Association of Watch and Clock Collectors (NAWCC) journal.  Here is a perfectly fine running clock with possibly the poorest choice of tooth form available...triangles.  Ha!  


And yet................it has been working for centuries.

So, my advice is to make whatever tooth form strikes your fancy and compare it against the "perfect" involute tooth forms and see how much difference it makes in the running of your clock.

Enjoy!  Aloha.  Clayton

12/18/21

Kinetic Sculpture and Clock Escapement Escapades

Escapements are fascinating.  Escapements add interest and movement to a clockworks since the escapement is the most active part of any clock.  And there are such a variety of ways that people have invented to allow the catch-and-release of the power that is being transmitted through a clock's train of gears.  But sometimes we don't need to build an entire clock to appreciate the movement of an escapement.  Escapements can be kinetic sculptures in themselves, and especially fun when they are anthropomorphized, or made to represent some beast.  Here are a couple of examples.

In this first short video, called "Tasty Fingers", the creature, with its teeth bared, is trying to take a bite from each of the fingers as they come around.  But the creature misses every time, which causes his hat to raise in surprise.  He is thinking, "Maybe the next finger will be the tasty one."



This is a video of the "Sipping Flowers" escapement in which a bird is sitting balanced atop a flower that is rocking with the pendulum.  And each time the flower rocks, the bird sticks his beak into the other flower (the escape wheel) to take a sip.


A wide variety of interesting escapements can be seen throughout the clock and kinetic sculpture  plans shown on my main page.  Compare the escapement of Solaris with that of Simplicity or Bird of Paradise or Harmonic Oscillator.  They are all so different and wonderful.

11/3/21

Sometimes Reality Doesn't Cooperate: The Monotonous Pi Clock

Not all clock plans make it for sale on my website.  This is the story of Pi.


Above:  Monotonous Pi 3D Renderings made from my dxfs
by my friend, Oleg in Russia

Below:  Pi, actually built by me, in motion below:



The Monotonous Pi is a kinetic sculpture posing as a clock. It has all the parts of both a clock and a kinetic sculpture. That huge circular pendulum has a very slow forward and back oscillation of approximately 38 beats a minute. Monotonous Pi has its roots in the Medieval 1300’s when the verge and foliot clocks were the techie’s state of the art timepieces. They weren’t very accurate. They could be off twenty minutes a day…plus or minus. That’s a pretty huge possible error spread, and that error rate in timekeeping, with only slight improvements, continued until the late 1600’s when the seconds pendulum was introduced by Galileo and others - like Christiaan Huygens (who, in my opinion, never gets enough credit). But not all verge and folio clocks had such problems with accuracy. Christiaan Huygens (1629-1695) had a suggestion that I’ve incorporated into all of my verge and folio clock designs (except Monotonous Pi), and they are actually quite accurate timekeepers. Huygens recommended a return spring on the verge to increase the clock’s accuracy. My designs, other than Pi, have just such a return spring which is created by the spread of the cord from which the verge and foliot is suspended. Most verge and foliots in those early days were suspended by a single strand of silk. By changing over to a loop of cord we can add that return spring advantage to our verge and foliot clocks that Huygens suggested, and this simple improvement increases their accuracy dramatically. You can see that loop of cord suspending the verge and foliot in my Medieval Rack, Holologium, and Wee Willie designs. But…Monotonous Pi is not one with a looped suspension cord or return spring, so its accuracy is very similar to the workings of those early Medieval clocks - which is not very good…but sometimes it’s right! However, on the other hand, as a kinetic sculpture the Monotonous Pi is excellent! Pi is a visual delight. It is lovely to watch Pi’s slow oscillating movement forward and back. And it does try so hard to keep good time, even though it’s not very good at it. Still…Monotonous Pi is one of my favorite sculptures. Pi is truly a delight to watch.

Aloha, Clayton

10/16/21

NEW! The Mantis Clock

 

Mantis by Clayton Boyer

Mantis has a large, slow, two second beat compound balance pendulum.  The pendulum on Mantis is about 46" (117cm) making it actually longer than a regular straight, hanging seconds pendulum, which are usually around 42" (107cm).   However to get a straight, hanging pendulum to tick at a two second beat, that pendulum would have to be over thirteen feet long.  Because Mantis uses a compound balance pendulum, we were able to create not only a dramatically shorter pendulum, but one with an artistic flare that beautifully accents this clock.

Mantis has a special escapement that allows for a very large and dramatic pendulum arc.  With its pendulum swinging with about forty degrees of arc, it makes Mantis as much a kinetic sculpture as it is a clock. The way the Mantis escapement is designed helps modulate its tone and creates a slow, gentle "tick" with each contact with an escape wheel tooth.  The slow swing and gentle sound of the pendulum is relaxing and mesmerizing, and the movement is a delight to view.


Mantis by Clayton Boyer

Hiding behind the mobile crescent at the right side of the dial ring is a motorized remontoir making daily rewinding of this beautiful sculpture unnecessary. The clock is powered by a weighted motor arm that automatically rewinds the clock.  The amount of drive weight is adjustable by simply changing the amount hanging from the cord on the right of the clock.  The difficult part for me was determining what to hang there.  There are so many beautiful options.  I tried various rocks (which looked pretty nice), glass spheres, a painted fishing weight, and finally settled on the clean look of copper tube.  That tube weighs 3.6oz (102gm), and to avoid over stressing the motor, the amount of added weight drive should be 8oz (227gm) or less.  The rewinding of the remontoir motor arm is powered by an onboard nine volt battery which will keep the clock running for about three to four months.

Mantis has movement throughout its design - from the massive swing of the pendulum, to the remontoir motor arm actuating the bobblehead and crescent that accent Mantis' "broken" dial ring.  The Organic clock design also has a "broken" dial, however that design is mainly aesthetic.  The dial ring of the Mantis is "broken" for a different reason - which is to allow the viewer a better view of the internal workings of this sculpture. 

Mantis was named because of the similarities between the antennae of a praying mantis and the upper part of the Mantis' double split pendulum.  As it happened, the day before the Mantis was completed we were  surprised to see that the Mantis clock had been visited by its namesake, a praying mantis. Shown going for a ride on the bobblehead in the picture below.  The praying mantis spent the night hanging out on the bobblehead, however I still needed to add the decorative brass screws, so I moved him/her to the nearest rosebush.  Obviously, such serendipity must equate, in some way, to a celebrity endorsement!


A Mantis on Mantis
Enjoy, Clayton Boyer

3/7/21

Beautiful Video on Making a Wooden Clock by Rasim Ramadan

 


"A Clock from the Fairy Tales"

Excellent and beautifully made video by builder Rasim Ramadan showing his Organic Clock build. 

Enjoy!  Clayton

11/19/20

Troubleshooting the Dial Train when the clock runs well but the hands are not turning correctly

Modern Times Clock
(just some eye candy unrelated to this post)


Berry writes:  I have everything completed now on the clock but having issues (I bet you hate letters like this). The motor drives the Center Wheel just fine. The Third Wheel and Escape Wheel and Pallet chug along day and night. It looks great. Unfortunately the Minute and Hour hands don't keep the time. I marked the Center Arbor Tube and Hour Arbor Tube with a spot of ink at the top. After one hour they were at the 9 o'clock position. Fifteen minutes later they're both back at 12.

I've no idea if you can help, but I'm hoping you can.

Best wishes - stay healthy, Berry


Aloha Berry, if I understand correctly, it sounds like something is slipping or some glue joint may have come apart.

Here are some of the places that slippage may occur in the dial train of these wonderful mechanisms....

Check to make sure that the center wheel tube is pressed tightly inside the center wheel.  That tube should travel with the center wheel and make one revolution every 60 minutes.  

To that tube is added the cannon pinion and its tube.  The cannon is held to the center wheel tube by the leather plug system that allows for synchronous movement of the minute and hour hands.  The minute hand is attached to the other end of the tube that is tight inside the cannon.  Make sure that the tube is tight inside the cannon and minute hand and they are not slipping.

The clock will run like that and show the minutes, but we need to also see what hour it is, so take off the minute hand from the cannon tube and slide the intermediate wheel onto its rod.  The cannon can now drive the intermediate wheel.  The intermediate wheel has glued to it a pinion.  Make sure that glue joint between the intermediate wheel and it pinion is tight.  

The intermediate pinion drives the hour wheel.  The hour wheel has a tube pressed tightly into its center.  Make sure that tube in the hour wheel is not slipping.  On the other end of that hour tube the hour hand is pressed on tightly.  Check to be sure that hand it tight to the hour tube as well.  Once you have slid the hour wheel/tube/hand assembly onto the cannon/tube assembly then you can press on the minute hand.  The minute hand should be tight to the tube.

Somewhere in that system from center wheel to minute hand, something is slipping...OR...

OR, it may not be slipping at all, possibly just the opposite.  

There is a possibility that the three tubes are binding somewhere and not running freely with each other.  The center wheel tube, and the cannon's minute tube and the hour tube must all be able to turn smoothly and easily on each other, and the center wheel tube needs to turn freely on the center wheel arbor.

If, for example, you forgot to put the leather plug in the cannon pinion and screwed the set screw directly into the center wheel tube then that tube will be dented and it will not move freely on the center wheel arbor.  That dent will cause the tube to stick to the rod and not move freely.

Sometimes tubes get dented or bent in other ways and will not turn freely on the rod or tube they mate with.  Test all tubes for free motion.

Sometimes after the rod or tube has been newly cut there are residual barbs and metal fragments on their ends that need to be cleaned up and removed.  Polishing the arbors and cleaning up the cut ends of the rods and tubes helps this tremendously.

All of the rods and various tubes must run easily on their mating rod or tube.  

Hopefully this gets your clock running nicely.  If not, send me a video showing what's happening and I can probably make a better diagnosis.

Enjoy! and send pix when you get your project completed.

Aloha.  Clayton